Premolten calcium aluminate refining slag

Release time: 2018-06-20 16:35:34 Page viewed: 161

Keywords

synthetic calcium aluminate slags, premelted refining slags, calcium aluminate, premelted calcium aluminate, flux

Introduction

At present, most steel plants in the world generally adopt Ladle refining, to reduce gas inclusion and make molten stell evenly, in order to realize high yield, high quality and low cost steel making. So Synthetic Calcium Aluminate Slags is designed and manufactured to meet the above requirement and take a very important role in steel refining.

TRADE MARK: HNKINGWAY

Properties

Low molten point, fast molten, shorten refining time and energy consuming.

Good fuidity, desulphurization and inclusion reducing

No flame, little dust emission and good safety in use

No water absorption and no metamorphosing

Effectual submerged arc, and reduce electric arc to burn and erode ladle lining, and enhance ladle life.

TRADE MARK: HNKINGWAY

Specification

1. CaO: 49 - 54% Al2O3: 41 - 45% SiO2: 3.8% max. TiO2: 2.8% max. Fe2O3: 1.8% max. MgO: 2.0% max.

2. CAO : 53% - 56% , AL2O3 : 32% - 37% , SIO2 : 4%MAX , FE2O3 : 1.5% MAX , MGO : 3% MAX , P : 0.05% MAX , S : 0.1% MAX 

TRADE MARK: HNKINGWAY

3. Al2O3  39 - 43%  CaO   32 - 36% SiO2  5.5% max Fe2O3  3% max TiO2: 4% max MgO: 11 - 15%

4. CaO: 47-53%, Al2O3: 43-49%, TiO2: 0.05% max, Fe2O3: 0.15% max, SiO2: 1% max, MgO: 0.2% max, S: 0.08 max

5. CaO 48-53 %, Al2O3 38-43 %, SiO2 3.5 %MAX, TiO2 2 % MAX, Fe2O3 1.2 % MAX

6. MgO 10,5 % min, CaO 22,0 % min. Al2O3 49,5 % min. SiO2 7,0 % max. Fe2O3 3,5 % max.

TiO2 4,0 % max.

7. CaO 33% Min. Al2O3 50-55% SiO2 6.0% Max. TiO2 4.0% Max. MgO 2.0% Max.Fe2O3 2.5% Max.

8. CaO : 47-56%, Al2O3 : 35-44%, SiO2: 5% max. Fe2O3: 2.0% max. P: 0.15% max, S: 0.15% max

9. MgO:11.0% min, CaO:32 % min, Al2O3:39% min, SiO2 : 5.5% max, Fe2O3:3.0% max, TiO2 : 4.0% max 

TRADE MARK: HNKINGWAY

10. CaO: 45 - 52%, Al2O3: 33-40%, MgO: 8-15%, SiO2: 3% max, S: 0.1% max, P: 0.05% max, TiO2: 0.06% max

Size: 0-30 mm

Melting point: 1350 C max

Principal mineralogical phase: C12A7

CAS No.: 65997-16-2 or 12042-68-1

Other specification can be manufactured according to customers requirement.

TRADE MARK: HNKINGWAY

Application Method

Adding Calcium Aluminate into in the furnace. Dosage: one ton molten steel needs Calcium Aluminate around 2-10 kg, and density of molten steel is greater than Calcium Aluminate. Then, argon gas is pumped in from the bottom of furnace, it drives the calcium aluminate to mix with the molten steel completely. Meanwhile, the molten Calcium aluminate adsorbs sulphur substance. Finally, dregs will suspend on the surface of molten steel due to it’s low density and can also keep warmness.

Application Functions

Desulphurization

Deoxygenation

Impurities absorption

Ladle lining protection

Packing

1200KG, 1000KG per sack